首先受邀花生壳公司送我蒲公英测试,我最明显要做的事情就是拆拆拆.
到我手的东西没有不拆的道理.首先这次LED是独立LED组成,不是RGB LED了,导光出去了.
然后发现2G,5G是两个不同芯片做的,走线是差分对都是X6左右,看似是PCI的.毕竟这个CPU支持.红色是射频芯片,黄色主芯片,不用拆也知道是MT7621,蓝色是内存,天蓝色是Flash.内存型号是NT5CB128M16FP,Flash是GD25Q128,这样的天线布局,在同等距离下,会比newifi差一些.
还有个NAND焊盘看来可以做点什么文章.Flash是GD的,之前还说GD的不怎么的,现在出货真大啊.
再细致看看NAND焊盘,卧槽,电容掉了.
当然其实最感兴趣和最想找的就是串口,这样对开SSH什么很有希望.一个是I2C一个是UART.
其他都是电源芯片我就懒得看了.只知道背面有1117,用MP1471AGJ做电源输入的最前级.其他配置就公版化了.蒲公英自己配了12V,差不多.先做了个串口调试引脚.
焊接能力超丑的不要见怪.用115200 boot进去了.
到终端时候直接回车就可以.试探了一下自带SSH.只是默认没启动.但是我发现使用enable指令也不能开机启动.
但是www目录下明显有猛料.
那个luci_index.html还是保留着的.打开看看.
非常好,其实不开盖也可以root,不过需要知道网页路径.root密码就是后台密码,默认admin.默认服务没开.
发一下启动日志.
[ 0.000000] [ 0.000000] The CPU feqenuce set to 880 MHz [ 0.000000] GCMP present [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] Software DMA cache coherency [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x0fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x0fffffff] [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] free_area_init_node: node 0, pgdat 80393f80, node_mem_map 8100000 0 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s6720 r8192 d13760 u32768 [ 0.000000] pcpu-alloc: s6720 r8192 d13760 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 65024 [ 0.000000] Kernel command line: board=HCMT7621-S256 console=ttyS1,115200 ro otfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00001017 [ 0.000000] Readback ErrCtl register=00001017 [ 0.000000] Memory: 255584k/262144k available (3042k kernel code, 6560k reser ved, 699k data, 220k init, 0k highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS1] enabled [ 0.120000] Calibrating delay loop... 577.53 BogoMIPS (lpj=2887680) [ 0.180000] pid_max: default: 32768 minimum: 301 [ 0.180000] Mount-cache hash table entries: 512 [ 0.190000] launch: starting cpu1 [ 0.190000] launch: cpu1 gone! [ 0.190000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.190000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es [ 0.190000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.190000] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.250000] Synchronize counters for CPU 1: done. [ 0.260000] launch: starting cpu2 [ 0.260000] launch: cpu2 gone! [ 0.260000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.260000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es [ 0.260000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.260000] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.320000] Synchronize counters for CPU 2: done. [ 0.330000] launch: starting cpu3 [ 0.330000] launch: cpu3 gone! [ 0.330000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.330000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es [ 0.330000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.330000] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.390000] Synchronize counters for CPU 3: done. [ 0.400000] Brought up 4 CPUs [ 0.400000] NET: Registered protocol family 16 [ 0.410000] MIPS: machine is OrayBox X5-1253 [ 0.710000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.710000] PCIE PHY initialize [ 0.720000] ***** Xtal 40MHz ***** [ 0.720000] start MT7621 PCIe register access [ 1.310000] RALINK_RSTCTRL = 7000000 [ 1.320000] RALINK_CLKCFG1 = 77ffeff8 [ 1.320000] [ 1.320000] *************** MT7621 PCIe RC mode ************* [ 1.820000] PCIE2 no card, disable it(RST&CLK) [ 1.820000] pcie_link status = 0x3 [ 1.830000] RALINK_RSTCTRL= 3000000 [ 1.830000] *** Configure Device number setting of Virtual PCI-PCI bridge *** [ 1.840000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 [ 1.840000] PCIE0 enabled [ 1.840000] PCIE1 enabled [ 1.850000] interrupt enable status: 300000 [ 1.850000] Port 1 N_FTS = 1b105000 [ 1.850000] Port 0 N_FTS = 1b105000 [ 1.860000] config reg done [ 1.860000] init_rt2880pci done [ 1.860000] FPU Affinity set after 11720 emulations [ 1.870000] bio: create slab <bio-0> at 0 [ 1.870000] i2c-gpio i2c-gpio.0: using pins 3 (SDA) and 4 (SCL) [ 1.880000] PCI host bridge to bus 0000:00 [ 1.880000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.890000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.890000] pci_bus 0000:00: No busn resource found for root bus, will use [b us 00-ff] [ 1.900000] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.900000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x7fffffff] [ 1.900000] pci 0000:00:00.0: reg 14: [mem 0x60300000-0x6030ffff] [ 1.900000] pci 0000:00:00.0: supports D1 [ 1.900000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.900000] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.900000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x7fffffff] [ 1.900000] pci 0000:00:01.0: reg 14: [mem 0x60310000-0x6031ffff] [ 1.900000] pci 0000:00:01.0: supports D1 [ 1.900000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.900000] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000 [ 1.900000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x000fffff] [ 1.900000] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.900000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.900000] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000 [ 1.900000] pci 0000:02:00.0: reg 10: [mem 0x00000000-0x000fffff 64bit] [ 1.900000] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0000ffff pref] [ 1.900000] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 1.900000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.900000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02 [ 1.900000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) [ 1.900000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) [ 1.910000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.910000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] [ 1.920000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref ] [ 1.920000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] [ 1.930000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] [ 1.930000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff] [ 1.940000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.940000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.950000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bi t] [ 1.950000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref ] [ 1.960000] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.960000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 1.970000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref ] [ 1.970000] BAR0 at slot 0 = 0 [ 1.980000] bus=0x0, slot = 0x0 [ 1.980000] BAR0 at slot 1 = 0 [ 1.980000] bus=0x0, slot = 0x1 [ 1.980000] bus=0x1, slot = 0x0, irq=0x4 [ 1.990000] bus=0x2, slot = 0x1, irq=0x18 [ 1.990000] Switching to clocksource MIPS [ 2.000000] NET: Registered protocol family 2 [ 2.000000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 2.000000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 2.010000] TCP: Hash tables configured (established 2048 bind 2048) [ 2.010000] TCP: reno registered [ 2.020000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.020000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.030000] NET: Registered protocol family 1 [ 2.030000] PCI: CLS 80 bytes, default 32 [ 2.260000] 4 CPUs re-calibrate udelay(lpj = 2924544) [ 2.280000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.290000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc. [ 2.300000] msgmni has been set to 499 [ 2.300000] io scheduler noop registered [ 2.300000] io scheduler deadline registered (default) [ 2.310000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.320000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A [ 2.320000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A [ 2.340000] brd: module loaded [ 2.340000] flash manufacture id: c8, device id 40 18 [ 2.350000] chip info: gd25q128b(c8 4018c840) [ 2.350000] mtd name = raspi, size = 0x01000000 (16M) erasesize = 0x00010000 (64K) [ 2.390000] Creating 6 MTD partitions on "raspi": [ 2.400000] 0x000000000000-0x000000030000 : "u-boot" [ 2.400000] 0x000000030000-0x000000040000 : "kpanic" [ 2.410000] mtdoops: MTD partition 1 not big enough for mtdoops [ 2.420000] 0x000000040000-0x000000050000 : "factory" [ 2.420000] 0x000000fe0000-0x000000ff0000 : "bdinfo" [ 2.430000] 0x000000ff0000-0x000001000000 : "reserve" [ 2.430000] 0x000000050000-0x000000fe0000 : "firmware" [ 2.440000] 2 uimage-fw partitions found on MTD device firmware [ 2.450000] 0x000000050000-0x0000001a0000 : "kernel" [ 2.450000] 0x0000001a0000-0x000000fe0000 : "rootfs" [ 2.460000] mtd: device 7 (rootfs) set to be root filesystem [ 2.460000] mtd: partition "rootfs_data" created automatically, ofs=0xab0000, len=0x530000 [ 2.470000] 0x000000ab0000-0x000000fe0000 : "rootfs_data" [ 2.480000] PROC INIT OK! [ 3.360000] rtc-pt7c4338 0-0068: rtc core: registered pt7c4338 as rtc0 [ 3.360000] i2c /dev entries driver [ 3.370000] Stopped WatchDog Timer. [ 3.370000] Ralink APSoC Hardware Watchdog Timer [ 3.370000] TCP: cubic registered [ 3.380000] NET: Registered protocol family 17 [ 3.380000] 8021q: 802.1Q VLAN Support v1.8 [ 4.270000] rtc-pt7c4338 0-0068: hctosys: unable to read the hardware clock [ 4.270000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", erro r -19 [ 4.280000] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 4.290000] Freeing unused kernel memory: 220K (803a9000 - 803e0000) [ 4.950000] Started WatchDog Timer. [ 6.560000] usbcore: registered new interface driver usbfs [ 6.560000] usbcore: registered new interface driver hub [ 6.570000] usbcore: registered new device driver usb [ 6.600000] SCSI subsystem initialized [ 6.610000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.620000] ehci-platform: EHCI generic platform driver [ 6.630000] libata version 3.00 loaded. [ 6.640000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.650000] *****run project phy. [ 6.670000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.690000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.710000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.730000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.750000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.770000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.790000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.810000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.830000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.850000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.910000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.930000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.950000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.970000] FM_OUT value: u4FmOut = 0(0x00000000) [ 6.990000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.010000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.030000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.050000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.070000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.090000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.240000] xhci-hcd xhci-hcd: xHCI Host Controller [ 7.240000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 [ 7.250000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000 [ 7.260000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.260000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 7.270000] usb usb1: Product: xHCI Host Controller [ 7.270000] usb usb1: Manufacturer: Linux 3.10.49 xhci-hcd [ 7.280000] usb usb1: SerialNumber: xhci-hcd [ 7.280000] xHCI xhci_add_endpoint called for root hub [ 7.280000] xHCI xhci_check_bandwidth called for root hub [ 7.280000] hub 1-0:1.0: USB hub found [ 7.290000] hub 1-0:1.0: 2 ports detected [ 7.290000] xhci-hcd xhci-hcd: xHCI Host Controller [ 7.300000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 [ 7.300000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 7.310000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 7.320000] usb usb2: Product: xHCI Host Controller [ 7.320000] usb usb2: Manufacturer: Linux 3.10.49 xhci-hcd [ 7.330000] usb usb2: SerialNumber: xhci-hcd [ 7.330000] xHCI xhci_add_endpoint called for root hub [ 7.330000] xHCI xhci_check_bandwidth called for root hub [ 7.330000] hub 2-0:1.0: USB hub found [ 7.340000] hub 2-0:1.0: 1 port detected [ 7.350000] sdhci: Secure Digital Host Controller Interface driver [ 7.360000] sdhci: Copyright(c) Pierre Ossman [ 7.360000] sdhci-pltfm: SDHCI platform and OF driver helper [ 7.370000] usbcore: registered new interface driver usb-storage [ 7.730000] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 26 of xdatum (0 unchecked, 25 orphan) and 74 of xref (0 dead , 65 orphan) found. [ 9.480000] NET: Registered protocol family 10 [ 9.500000] RPC: Registered named UNIX socket transport module. [ 9.510000] RPC: Registered udp transport module. [ 9.510000] RPC: Registered tcp transport module. [ 9.520000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.540000] tun: Universal TUN/TAP device driver, 1.6 [ 9.540000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 9.550000] l2tp_core: L2TP core driver, V2.0 [ 9.560000] l2tp_netlink: L2TP netlink interface [ 9.570000] gre: GRE over IPv4 demultiplexor driver [ 9.570000] ip_gre: GRE over IPv4 tunneling driver [ 9.600000] nf_conntrack version 0.5.0 (3996 buckets, 15984 max) [ 9.620000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.630000] Netfilter messages via NETLINK v0.30. [ 9.630000] ip_set: protocol 6 [ 9.670000] u32 classifier [ 9.670000] input device check on [ 9.670000] Actions configured [ 9.680000] Mirror/redirect action on [ 10.020000] MT7603E module init [ 10.030000] MT7603E AP Driver version-4.0.1.0rev2.P1 [ 10.650000] MT7612E module init [ 10.660000] MT76x2 AP Driver version-3.0.4.0.P1.20150909 [ 11.290000] MTK MSDC device init. [ 11.310000] msdc0 -> ================ <- msdc_set_mclk() : L<686> PID<kmodloa der><0x3aa> [ 11.310000] msdc0 -> !!! Set<400KHz> Source<50000KHz> -> sclk<390KHz> <- msdc _set_mclk() : L<687> PID<kmodloader><0x3aa> [ 11.320000] msdc0 -> ================ <- msdc_set_mclk() : L<688> PID<kmodloa der><0x3aa> [ 11.350000] msdc0 -> ops_get_cd return<1> <- msdc_ops_get_cd() : L<2343> PID< kworker/u8:0><0x6> [ 11.350000] mtk-sd: MediaTek MT6575 MSDC Driver [ 11.350000] usbcore: registered new interface driver cdc_acm [ 11.350000] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters [ 11.350000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.380000] msdc0 -> XXX MSDC_INT_SDIOIRQ <- msdc_irq() : L<2419> [ 11.380000] msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.390000] msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.400000] msdc0 -> XXX CMD<8> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.410000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.420000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.420000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.430000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.440000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.440000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.450000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.460000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.460000] nf_conntrack_rtsp v0.6.21 loading [ 11.460000] msdc0 -> XXX CMD<1> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.470000] msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<634> PID<kworker /u8:0><0x6> [ 11.470000] msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<634> PID<kworker /u8:0><0x6> [ 11.490000] msdc0 -> ================ <- msdc_set_mclk() : L<686> PID<kworker /u8:0><0x6> [ 11.490000] msdc0 -> !!! Set<300KHz> Source<50000KHz> -> sclk<297KHz> <- msdc _set_mclk() : L<687> PID<kworker/u8:0><0x6> [ 11.490000] msdc0 -> ================ <- msdc_set_mclk() : L<688> PID<kworker /u8:0><0x6> [ 11.510000] msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<8> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> XXX CMD<1> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.510000] msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<634> PID<kworker /u8:0><0x6> [ 11.520000] msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<634> PID<kworker /u8:0><0x6> [ 11.540000] msdc0 -> ================ <- msdc_set_mclk() : L<686> PID<kworker /u8:0><0x6> [ 11.540000] msdc0 -> !!! Set<260KHz> Source<50000KHz> -> sclk<255KHz> <- msdc _set_mclk() : L<687> PID<kworker/u8:0><0x6> [ 11.540000] msdc0 -> ================ <- msdc_set_mclk() : L<688> PID<kworker /u8:0><0x6> [ 11.560000] msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<8> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.560000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.570000] msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.570000] msdc0 -> XXX CMD<1> MSDC_INT_CMDTMO <- msdc_irq() : L<2487> [ 11.570000] msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<634> PID<kworker /u8:0><0x6> [ 11.850000] nf_nat_rtsp v0.6.21 loading [ 11.860000] usbcore: registered new interface driver usbserial [ 11.870000] usbcore: registered new interface driver usbserial_generic [ 11.880000] usbserial: USB Serial support registered for generic [ 11.910000] xt_time: kernel timezone is -0000 [ 11.930000] PPP generic driver version 2.4.2 [ 11.930000] PPP MPPE Compression module registered [ 11.940000] NET: Registered protocol family 24 [ 11.940000] PPTP driver version 0.8.5 [ 11.950000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 11.960000] usbcore: registered new interface driver option [ 11.970000] usbserial: USB Serial support registered for GSM modem (1-port) [ 15.040000] phy_free_head is 0xdaa2000!!! [ 15.040000] phy_free_tail_phy is 0xdaa3ff0!!! [ 15.050000] txd_pool=adb90000 phy_txd_pool=0DB90000 [ 15.050000] ei_local->skb_free start address is 0x8fef54c4. [ 15.060000] free_txd: adb90010, ei_local->cpu_ptr: 0DB90000 [ 15.060000] POOL HEAD_PTR | DMA_PTR | CPU_PTR [ 15.070000] ----------------+---------+-------- [ 15.070000] 0xadb90000 0x0DB90000 0x0DB90000 [ 15.080000] [ 15.080000] phy_qrx_ring = 0x0f7c7000, qrx_ring = 0xaf7c7000 [ 15.090000] [ 15.090000] phy_rx_ring0 = 0x0da56000, rx_ring0 = 0xada56000 [ 16.250000] ra2880stop()...Done [ 16.250000] Free TX/RX Ring Memory! [ 16.260000] phy_free_head is 0xd116000!!! [ 16.270000] phy_free_tail_phy is 0xd117ff0!!! [ 16.270000] txd_pool=adbbc000 phy_txd_pool=0DBBC000 [ 16.280000] ei_local->skb_free start address is 0x8fef54c4. [ 16.280000] free_txd: adbbc010, ei_local->cpu_ptr: 0DBBC000 [ 16.290000] POOL HEAD_PTR | DMA_PTR | CPU_PTR [ 16.290000] ----------------+---------+-------- [ 16.300000] 0xadbbc000 0x0DBBC000 0x0DBBC000 [ 16.300000] [ 16.300000] phy_qrx_ring = 0x0f675000, qrx_ring = 0xaf675000 [ 16.310000] [ 16.310000] phy_rx_ring0 = 0x0db78000, rx_ring0 = 0xadb78000 [ 16.340000] device eth0 entered promiscuous mode [ 16.340000] br-lan: port 1(eth0) entered forwarding state [ 16.350000] br-lan: port 1(eth0) entered forwarding state [ 16.540000] device ra0 entered promiscuous mode [ 16.550000] br-lan: port 2(ra0) entered forwarding state [ 16.550000] br-lan: port 2(ra0) entered forwarding state [ 17.020000] device rai0 entered promiscuous mode [ 17.030000] br-lan: port 3(rai0) entered forwarding state [ 17.030000] br-lan: port 3(rai0) entered forwarding state [ 18.350000] br-lan: port 1(eth0) entered forwarding state [ 18.550000] br-lan: port 2(ra0) entered forwarding state [ 18.640000] MT7621 GE2 link rate to 1G [ 18.730000] ethernet: port4 linkup(interrupt) [ 18.760000] ethernet: port2 linkup(interrupt) [ 19.030000] br-lan: port 3(rai0) entered forwarding state [ 524.260000] nf_conntrack: automatic helper assignment is deprecated and it wi ll be removed soon. Use the iptables CT target to attach helpers instead.
为了更好折腾,我觉得先备份Flash最好.然后scp拷贝过来.
还要备份一下overlays.
一切安好了.上螺丝.其他下回分解吧.
您好 我想获取X5 的 root access
我跟您一样焊接了串口调试， 但是界面一直卡在 /sbin/askfirst: Please press Enter to activate this console.
flow control 设置为 none
但是仍然卡在这里。 能否帮忙看一下。
@Ian 可能不是Enter键,可能是Ctrl+X(X可能是C,B,A….)改过很多次.
Usb ttl接的3.3v gnd tx rx么？然后用putty登录？
@wally497173256 3V3不用接,TX接RX,RX接TX,GND接GND.
大佬我留个QQ号跟你请教一下吧。497173256
NAND焊盘可以焊接上去做点文章么？
@wally497173256 并没用途.
@TaterLi 好的。谢谢大神的指导。后面还在逐步摸索中。
GD Flash 换 华邦的Flash应该不受影响吧。还没想硬改而已，不然换个更大的Flash和内存。
@wally497173256 256MBit是16位寻址,他已经拿到8位寻址最大的Flash了.
@TaterLi 好的。谢谢。
早上好，我想问一下不硬件改造的情况下改登录，能否把路由器LAN口改成WAN口，从而实现多WAN口。三线拨号。
@wally497173256 硬改也不行,这个CPU就四个口,其他一大排都是SWITCH扩展出来的,如果软件来做可以做虚拟网桥呗,就是速度不快.